Freight shows up, the rigging crew sets the machine, and then it sits there for two weeks because nobody sorted out the power. Craig Faria Electrician has handled industrial machine wiring and equipment installation in Taunton, MA, and nearby areas since 1996, and we've watched plenty of plants lose weeks to a hookup that should've been planned months earlier. Figuring out the electrical scope before equipment arrives is what keeps a capital purchase from turning into an expensive paperweight.
Craig Faria Electrician has operated from Taunton, MA, since 1996, serving industrial clients throughout Bristol and Plymouth counties. Our crew specializes in industrial machine wiring and equipment installation for manufacturing plants, processing facilities, and production lines, covering disconnects and feeders, motor circuits, control and sensor wiring, safety interlocks, VFD installation, conduit and cable tray, and commissioning support alongside your equipment vendor. Craig built the company from a single truck into a full industrial crew, and we hold membership in the Massachusetts Electrical Contractors Association.
Here's how it usually plays out. A plant orders a machine, the lead time runs six months, and everybody focuses on the mechanical install. The unit lands on the floor, and only then does somebody pull the spec sheet and realize it needs 480 three-phase at an amperage the nearest panel can't deliver.
The cause is a gap in who owns the electrical scope. Equipment vendors provide a spec and assume the site is ready, while plant maintenance stays busy keeping current production running. Nobody's job is to walk the distance from the panel to the new footprint, check what's available, and figure out the conduit route. Add older facilities where the as-builts stopped matching reality years ago, and the surprises multiply.
Doing it right means treating the hookup as part of the purchase rather than an afterthought. Our crew reviews the manufacturer's electrical spec, verifies available capacity at the panel, sizes the feeder and overcurrent protection, plans the conduit route around existing equipment and traffic, and schedules the work against your production calendar. Installation covers the disconnect, feeders, motor circuits, control wiring, sensors, safety interlocks, and any VFD or starter the equipment calls for, all labeled and documented. We stay on site through the vendor's commissioning so anything electrical gets resolved on the spot.
The result is equipment running the week it arrives instead of the month after. Documentation goes into your files so the next service call doesn't start with a hunt, and the labeling lets your maintenance team trace a circuit without guessing. Plants that bring us in during the quoting stage rarely deal with this problem twice.
Machine hookups look similar from the outside, though the details separate an install that lasts from one that generates service calls.
Production equipment runs at load for hours at a stretch, which is a different animal from the intermittent demand most wiring assumes. Conductors, breakers, and terminations all get sized for the real duty cycle rather than the nameplate minimum. Undersized feeders show up later as heat, voltage drop, and nuisance tripping.
Vibration, heat, coolant, and dust all attack control circuits in ways a clean office install never sees. Proper wire type, strain relief, sealed connections, and routing away from heat sources keep those circuits intact. Separating control runs from power runs also cuts down on the electrical noise behind a lot of phantom faults.
E-stops, light curtains, gate switches, and interlocks are the parts nobody thinks about until an audit or an incident. Each one gets wired exactly as the equipment manufacturer specifies and tested before the machine goes into service. Shortcuts here create liability nobody wants to carry.
Variable frequency drives save energy and extend motor life, though they're sensitive to cable type, run length, and grounding. Getting the shielded cable, bonding, and drive parameters right prevents bearing damage and the intermittent faults that follow a sloppy install. We coordinate with the drive manufacturer when a setup calls for it.
A panel schedule that matches reality saves hours on every future service call. Circuits get labeled at both ends, drawings get marked up with what was actually installed, and your maintenance team gets a copy. Everything we install also carries a one-year workmanship warranty.
Equipment installs tend to expose other things a facility needs, and our crew handles those as well.
Adding equipment eventually forces a harder look at what's feeding the building. Our industrial power distribution systems work covers panels, transformers, feeders, and switchgear built around the load your facility actually carries.
New equipment performs best when the rest of the electrical system is healthy. Industrial preventive maintenance and troubleshooting catches the loose terminations, failing breakers, and degrading connections that eventually take a line down.
Our full range of industrial electrical services covers generator installation, power distribution, machine wiring, maintenance, and emergency response for facilities across the region. Many plants keep us on call for whatever comes up.
Industrial work rewards experience more than almost any other kind of electrical job.
Craig started this company in 1996, and the crew has since wired equipment in manufacturing facilities, processing plants, and some genuinely rough environments, including complete asphalt plants. That background means we've already dealt with most of what a production floor throws at an installation.
Shutdown windows are short and expensive, so the electrical scope has to fit inside them. Nights, weekends, and holiday shutdowns are all normal for our crew. Planning the sequence beforehand keeps everybody productive during the hours you actually have.
Manufacturers have specific requirements, and misreading them costs everybody time. Our team goes through the electrical documentation before the job starts and talks directly with the vendor's technician during commissioning. Issues get sorted while the right people are still on site.
A machine that won't start after hours is a production problem rather than a scheduling problem. We take emergency calls and get someone to your facility instead of putting you in line behind next week's work.
Every installation gets performed by licensed electricians under a permit from the local wiring inspector and inspected before it goes into service. Belonging to the Massachusetts Electrical Contractors Association keeps our crew current as code evolves.
As early as the quoting stage, ideally. Reviewing the electrical spec before the order goes in tells you whether your existing service can support the machine or whether a distribution upgrade needs to happen alongside it. Plants in Taunton, Fall River, and New Bedford that wait until delivery routinely lose two to four weeks.
Regularly. Most of our industrial installs happen at night, on weekends, or during scheduled shutdowns, since that's when the floor is available. We plan the sequence in advance so the crew works straight through the window rather than waiting on access.
Yes, in nearly all cases. Electrical permits come from the wiring inspector in the city or town where the plant sits, and the installation gets inspected before it goes into service. We pull the permit and meet the inspector as part of the job.
That's most of what industrial work involves, and our crew is set up for it. Three-phase feeders, motor circuits, VFDs, and the distribution equipment behind them are all routine. Larger installs sometimes require utility coordination, which we handle too.
It happens more often than you'd think with imported equipment. Our team works from whatever documentation exists, contacts the manufacturer or the vendor's technician when something's unclear, and confirms requirements before energizing anything. Guessing on an industrial hookup isn't worth the risk.
FAQs reviewed by Craig Faria, a licensed electrician and owner of Craig Faria Electrician, serving industrial facilities throughout Taunton, MA, and the surrounding region.
Send us the electrical spec and the delivery date, and we'll tell you what the site needs before the machine ships. You'll get a scope, a schedule that fits your shutdown window, and a hookup that's ready when the rigging crew pulls out.
Business Name: Craig Faria Electrician
Address: Taunton, MA, 02780
Phone: 508-509-0076
Business Hours:
Mon - Fri: 7:00 AM to 3:00 PM
Sat-Sun: Closed
Emergency Service Available
One-year workmanship warranty.